.... Welcome toG
I'm sorry to hear about your issue. We will try to help you resolve this as soon
Your stop code indicates the below:
- Please understand we are all volunteers and we are not here all the time.
- Sometimes it may be a extended amount of time to get back to you. If it has been
more then 3 days please shoot me a PM and I will try to get back to you quickly
- Please do not reply to your own original most as much as you did because to us it looks like you are receiving help. This in turn would slow down anyone from who could possibly helping you to respond.
- Please do the following and supply the requested information as needed. If you
don't understand my instructions please ask and I will try to explain them
clearer for you.
- Do not attempt any steps unless instructed or ask before to
make sure they will not cause any further issues.
(Click to consult the online Win XP Resource Kit article.)
The system attempted to access pageable memory using a kernel process IRQL that was too high. The most typical cause is a bad device driver (one that uses improper addresses). It can also be caused by caused by faulty or mismatched RAM, or a damaged pagefile.
and then to Run
Type in Chkdsk /r
Note the space between k and /
...It will probably ask if you want to do this on the next reboot...click Y
If the window doesn't shutdown on its own then reboot the system manually. On reboot the system will start the chkdsk operationThis one will take longer then chkdsk /f
Note... there are 5 stages
It may appear to hang at a certain percent for a hour or more or even back up and go over the same area...this is normal...DO NOT SHUT YOUR COMPUTER DOWN WHILE CHKDSK IS RUNNING OR YOU CAN HAVE SEVERE PROBLEMS
This can take several hours to complete.
When completed it will boot the system back into windows.
Let me know if this fixes the problem
How To Run Chkdsk /r from Recovery Console:
How to run checkdisk from recovery console (Windows xp). (Courtesy dsenette)
- Insert the Windows XP startup disk into the floppy disk drive, or insert the Windows XP CD-ROM into the CD-ROM drive, and then restart the computer.
Note:Click to select any options that are required to start the computer from the CD-ROM drive if you are prompted to do so.
- When the "Welcome to Setup" screen appears, press R to start the Recovery Console.
Note:If you have a dual-boot or multiple-boot computer, select the installation that you want to access from the Recovery Console.
- When you are prompted to do so, type the Administrator password. If the administrator password is blank, just press ENTER.
- At the Recovery Console command prompt, type the following then press Enter:
- Allow this to run UNDISTURBED until completed (45 min or so)
- Report any errors
If you have more than one RAM module installed, try starting computer with one RAM stick at a time.NOTE Keep in mind, the manual check listed above is always superior to the software check, listed below. DO NOT proceed with memtest, if you can go with option AB.
If you have only one RAM stick installed...
1. Download - Pre-Compiled Bootable ISO (.zip)
2. Unzip downloaded memtest86+-2.11.iso.zip
3. Inside, you'll find memtest86+-2.11.iso
4. Download, and install ImgBurn
5. Insert blank CD into your CD drive.
6. Open ImgBurn
, and click on Write image file to disc
7. Click on Browse for a file...
8. Locate memtest86+-2.11.iso
file, and click Open
9. Click on ImgBurn green arrow to start burning bootable memtest86 CD:
10. Once the CD is created, boot from it, and memtest will automatically start to run. You may have to change the boot sequence in your BIOS to make it work right.
To change Boot Sequence
in your BIOS
Reboot the system and at the first post screen (where it is counting up memory)
start tapping the DEL
This will enter you into the Bios\Cmos
Find the Advanced
area and click Enter
Look for Boot Sequence
or Boot Options
and highlight that click Enter
Now highlight the first drive and follow the directions on the bottom of the screen on how to modify it and change it to CDrom
Change the second drive to the C or Main Drive
Once that is done then click F10 to Save and Exit
You will prompted to enter Y
to verify Save and Exit
. Click Y
and the system will now reboot with the new settings.
The running program will look something like this depending on the size and number of ram modules installed:
It's recommended to run 5-6 passes
. Each pass contains very same 8 tests
This will show the progress of the test. It can take a while. Be patient, or leave it running overnight.
The following image is the test results area:
The most important item here is the “errors” line. If you see ANY errors, even one, most likely, you have bad RAM.