[Gin68]

How do I find an solution to this problem:

The instruction at "0X097b0068" referenced memory at "0x097b0068". The memory could not be "written". This occurred when I tried to install an Active X control.

Thank you.

[Advertisements]

Hello Gin68.... Welcome to
GeeksToGo,


I'm sorry to hear about your issue. We will try to help you resolve this as soon as possible.

• Please understand we are all volunteers and we are not here all the time.
• Sometimes it may be a extended amount of time to get back to you. If it has been
  more then 3 days please shoot me a PM and I will try to get back to you quickly
  then.
• Please do the following and supply the requested information as needed. If you
  don't understand my instructions please ask and I will try to explain them
  clearer for you.
• Do not attempt any steps unless instructed or ask before to
  make sure they will not cause any further issues.
• If you are receiving assistance in any other forum site please let us know as there may be conflicting advice given.

Before we can help you need to provide the following so I can start you in the right direction.
Laptop or Desktop?

• If a name brand system then what brand, make and model is the system?
• If custom built then what brand, make and model is the motherboard
• Total memory installed
• Total hard drive capacity and free space
• What steps have you taken so far to resolve the issue

If you have more than one RAM module installed, try starting computer with one RAM stick at a time.

NOTE Keep in mind, the manual check listed above is always superior to the software check, listed below. DO NOT proceed with memtest, if you can go with option A

B. If you have only one RAM stick installed...
...run memtest...


1. Download - Pre-Compiled Bootable ISO (.zip). If you prefer to use the USB version then use this link USB KEY
2. Unzip downloaded /memtest86+-4.20.iso.zip file.
3. Inside, you'll find /memtest86+-4.20.iso file.
4. Download, and install ImgBurn: http://www.imgburn.com/
5. Insert blank CD into your CD drive.
6. Open ImgBurn, and click on Write image file to disc
7. Click on Browse for a file... icon:



8. Locate [b/memtest86+-4.20.iso[/b] file, and click Open button.
9. Click on ImgBurn green arrow to start burning bootable memtest86 CD:



10. Once the CD is created, boot from it, and memtest will automatically start to run. You may have to change the boot sequence in your BIOS to make it work right.

To change Boot Sequence in your BIOS

Reboot the system and at the first post screen (where it is counting up memory) start tapping the DEL button
This will enter you into the Bios\Cmos area.
Find the Advanced area and click Enter
Look for Boot Sequence or Boot Options and highlight that click Enter
Now highlight the first drive and follow the directions on the bottom of the screen on how to modify it and change it to CDrom.
Change the second drive to the C or Main Drive
Once that is done then click F10 to Save and Exit
You will prompted to enter Y to verify Save and Exit. Click Y and the system will now reboot with the new settings.


The running program will look something like this depending on the size and number of ram modules installed:




It's recommended to run 5-6 passes. Each pass contains very same 8 tests.

This will show the progress of the test. It can take a while. Be patient, or leave it running overnight.



The following image is the test results area:



The most important item here is the “errors” line. If you see ANY errors, even one, most likely, you have bad RAM.

[rshaffer61]

Hello Gin68.... Welcome to
GeeksToGo,


I'm sorry to hear about your issue. We will try to help you resolve this as soon as possible.

• Please understand we are all volunteers and we are not here all the time.
• Sometimes it may be a extended amount of time to get back to you. If it has been
  more then 3 days please shoot me a PM and I will try to get back to you quickly
  then.
• Please do the following and supply the requested information as needed. If you
  don't understand my instructions please ask and I will try to explain them
  clearer for you.
• Do not attempt any steps unless instructed or ask before to
  make sure they will not cause any further issues.
• If you are receiving assistance in any other forum site please let us know as there may be conflicting advice given.

Before we can help you need to provide the following so I can start you in the right direction.
Laptop or Desktop?

• If a name brand system then what brand, make and model is the system?
• If custom built then what brand, make and model is the motherboard
• Total memory installed
• Total hard drive capacity and free space
• What steps have you taken so far to resolve the issue

If you have more than one RAM module installed, try starting computer with one RAM stick at a time.

NOTE Keep in mind, the manual check listed above is always superior to the software check, listed below. DO NOT proceed with memtest, if you can go with option A

B. If you have only one RAM stick installed...
...run memtest...


1. Download - Pre-Compiled Bootable ISO (.zip). If you prefer to use the USB version then use this link USB KEY
2. Unzip downloaded /memtest86+-4.20.iso.zip file.
3. Inside, you'll find /memtest86+-4.20.iso file.
4. Download, and install ImgBurn: http://www.imgburn.com/
5. Insert blank CD into your CD drive.
6. Open ImgBurn, and click on Write image file to disc
7. Click on Browse for a file... icon:



8. Locate [b/memtest86+-4.20.iso[/b] file, and click Open button.
9. Click on ImgBurn green arrow to start burning bootable memtest86 CD:



10. Once the CD is created, boot from it, and memtest will automatically start to run. You may have to change the boot sequence in your BIOS to make it work right.

To change Boot Sequence in your BIOS

Reboot the system and at the first post screen (where it is counting up memory) start tapping the DEL button
This will enter you into the Bios\Cmos area.
Find the Advanced area and click Enter
Look for Boot Sequence or Boot Options and highlight that click Enter
Now highlight the first drive and follow the directions on the bottom of the screen on how to modify it and change it to CDrom.
Change the second drive to the C or Main Drive
Once that is done then click F10 to Save and Exit
You will prompted to enter Y to verify Save and Exit. Click Y and the system will now reboot with the new settings.


The running program will look something like this depending on the size and number of ram modules installed:




It's recommended to run 5-6 passes. Each pass contains very same 8 tests.

This will show the progress of the test. It can take a while. Be patient, or leave it running overnight.



The following image is the test results area:



The most important item here is the “errors” line. If you see ANY errors, even one, most likely, you have bad RAM.