Internet not working tcp/ip errors & other device manager errors
Posted 22 March 2012 - 05:25 PM
Posted 22 March 2012 - 05:45 PM
Is it on what is known as the I/O plate that is the Input Output, near to the usb ports and the monitor OR does it connect further down away from those.
Also if you look in Device Manager at the other device open the ethernet controller what please does it say
Posted 22 March 2012 - 06:05 PM
You then as explained here have to extract that file as it is a zip file. Then following the advice below did you get the on screen instructions at 8.
1.Double-click the new icon on the desktop labeled R78727.EXE.
2.The Self-Extracting window appears and prompts you to extract or
unzip to C:\DELL\DRIVERS\r78727. Write down this path so the executable (I.e.
Setup.exe) file can be found later.
3.The Self-Extractor window appears.
5.After completing the file extraction, if the Self-Extractor
window is still open, close it.
6.Click the Start button and then click Run.
7.Type C:\DELL\DRIVERS\r78727 in the Open textbox and then click OK.
8.Follow the on-screen installation instructions.
After doing that you restart the computer
YOUR network adaptor if it is the original one on the integrated LAN on the motherboard and not an added card should then not be in other devices it should have been noved to Network adaptors.
Posted 22 March 2012 - 06:05 PM
LAN 1 goes from the router to the computer
LAN 3 and 4 goes to this computer
The router runs from top to bottom
Restore Factory Settings
Location PCI bus 4 device 7 function 0
The driver for this device is not installed Code 28
You try to reinstall from the wizard and windows can't find the hardware. You try to roll back and it has no backup.
Posted 22 March 2012 - 06:12 PM
Posted 22 March 2012 - 06:26 PM
I quite understand how difficult this is for you.
WHERE is the ethernet cable connected ON YOUR computer
in amongst those connections shown on what I have told you is the I/O plate OR further down where on the image above you can see the basic illustration of where the added cards would be
Posted 22 March 2012 - 06:40 PM
The ethernet cable doesn't go to the computer. It only goes from modem and router. Then the 1 cord goes from the internet setting on my router to the computer with my bridge running my ps3 wireless or w/e.
Would you like a picture of the inside of the computer? The only thing that runs to the computer from either device goes into this little box called LS1002 0451 Falco.
I'm still probably not helping you much.
Posted 22 March 2012 - 06:49 PM
Posted 22 March 2012 - 07:05 PM
Posted 22 March 2012 - 07:12 PM
That was good sending those.
This confirms that it is using the onboard network chip.
Try this, go the other device and follow this procedure - manually installing the driver
To do so you will have to open that driver download you have to find the right file to point the installation to.
Here is the procedure but you can use the link as a guide if you wish
- To the "Can Windows connect to Windows Update to search for software?" question, choose the No, not this time radio button and then click the Next > button.
- To the "What do you want the wizard to do?" question, choose the Install from a list or specific location (Advanced) radio button and then click the Next > button.
The next window that appears will be the Please choose your search and installation options. window containing several radio buttons and checkboxes.
- Choose the Don't search. I will choose the driver to install. radio button and then click the Next > button.
- Click the Have Disk... button on the Select the device driver you want to install for this hardware. window.
- Click the Browse... button on the Install From Disk dialog box that appeared.
In the Locate File dialog box that appears next, navigate to the folder that you extracted as part of the driver download.
- Click the INF file that displays in the file list and click the Open button.
Note: Device Manager only reads INF files so you won't be able so select anything else. If you run in to trouble here, see the Tips at the bottom of this page.
- Click the OK button back on the Install From Disk dialog box.
- Choose the newly added hardware back on the Select the device driver you want to install for this hardware. window and then click the Next > button.
If you're warned about the software for the hardware device not passing the Windows Logo testing, click the Continue Anyway button. Many drivers are not Windows certified but are still safe to install.
- The Hardware Update Wizard will now use the instructions provided in the INF file from Step 11 to install the updated drivers for your hardware. Follow any additional instructions on screen to complete the driver update.
Posted 22 March 2012 - 07:22 PM
Please confirm WHERE the Falco LAN device IS
Posted 22 March 2012 - 07:36 PM
Which driver do you want me to try to manually install the Intel ® Pro/100 VE Network Manager or the chipset driver?
Posted 22 March 2012 - 07:52 PM
Posted 22 March 2012 - 07:57 PM
Posted 22 March 2012 - 08:03 PM