Well I went into the event viewer and i click on system, it then says this file is corrupt and it shows no errors. Any suggestions other than sys restore?

XP Freezes on startup
Started by
unknown error
, Apr 22 2005 01:09 PM
#1
Posted 22 April 2005 - 01:09 PM

Well I went into the event viewer and i click on system, it then says this file is corrupt and it shows no errors. Any suggestions other than sys restore?
#2
Posted 22 April 2005 - 01:20 PM

If it were me, I would delete the corrupt file and try to restat again
http://support.micro...b;EN-US;q172156
http://support.micro...b;EN-US;q172156
#3
Posted 22 April 2005 - 01:45 PM

DCOM got error "This service cannot be started in Safe Mode " attempting to start the service EventSystem with arguments "" in order to run the server:
{1BE1F766-5536-11D1-B726-00C04FB926AF}
-got that twice
The DHCP Client service depends on the NetBios over Tcpip service which failed to start because of the following error:
A device attached to the system is not functioning.
-got that about 6 times
The Workstation service terminated with service-specific error 2250 (0x8CA).
-twice
Could not load Rdbss device driver.
-twice
The Workstation service terminated with service-specific error 2250 (0x8CA).
An error was detected on device \Device\Harddisk0\D during a paging operation.
-disk error [alot]
DCOM got error "The service database is locked. " attempting to start the service netman with arguments "" in order to run the server:
{BA126AE5-2166-11D1-B1D0-00805FC1270E}
-3 times
{1BE1F766-5536-11D1-B726-00C04FB926AF}
-got that twice
The DHCP Client service depends on the NetBios over Tcpip service which failed to start because of the following error:
A device attached to the system is not functioning.
-got that about 6 times
The Workstation service terminated with service-specific error 2250 (0x8CA).
-twice
Could not load Rdbss device driver.
-twice
The Workstation service terminated with service-specific error 2250 (0x8CA).
An error was detected on device \Device\Harddisk0\D during a paging operation.
-disk error [alot]
DCOM got error "The service database is locked. " attempting to start the service netman with arguments "" in order to run the server:
{BA126AE5-2166-11D1-B1D0-00805FC1270E}
-3 times
#4
Posted 22 April 2005 - 02:27 PM

Don't worry about Dcom issues, most of the others are related to networking...if you are in safe mode, they will occur..
This one:
An error was detected on device \Device\Harddisk0\D during a paging operation.
-disk error [alot]
Not good--
How many harddrives?
This one:
An error was detected on device \Device\Harddisk0\D during a paging operation.
-disk error [alot]
Not good--
How many harddrives?
#5
Posted 22 April 2005 - 02:48 PM

Right now 2 but im only using 1 so the other one is just there doing nothing right now. I disabled DCOM anyway.
#6
Posted 22 April 2005 - 03:33 PM

Start > run
cmd
enter
chkdsk c: /r
say yes and reboot
After completed,
start > run
cmd
enter
chkdsk c: /r
repeat
cmd
enter
chkdsk c: /r
say yes and reboot
After completed,
start > run
cmd
enter
chkdsk c: /r
repeat
#7
Posted 22 April 2005 - 03:50 PM

Ok I did it once already [in safe mode] and i hit Y to restart and then it restarts and freezes on the log in screen like before.
Should I create a bootdisk with chkdsk on it? http://support.micro...om/?kbid=309000
Should I create a bootdisk with chkdsk on it? http://support.micro...om/?kbid=309000
Edited by unknown error, 22 April 2005 - 04:01 PM.
#8
Posted 22 April 2005 - 04:41 PM

I got a 98 bootcd with scandisk on it and tried to boot it up, nothing happend. I changed to boot order for it too.
#9
Posted 22 April 2005 - 05:09 PM

did you do it for both drives?
#10
Posted 22 April 2005 - 09:14 PM

Yeah still nothing happend. I think its somthing with the network because i can get into safe mode, but not with networking. And those error messages had to do with networking. So im going to try somthing and reply back.
#11
Posted 22 April 2005 - 09:51 PM

Got a new Stop Error:
Session3_Initilzation_Failed
Stop: 0x0000006f (0xc00000z0, 0x00000000, 0x00000000, 0x00000000)
that z could be a 2 or z not sure.
Session3_Initilzation_Failed
Stop: 0x0000006f (0xc00000z0, 0x00000000, 0x00000000, 0x00000000)
that z could be a 2 or z not sure.
#12
Posted 22 April 2005 - 10:21 PM

Removed Comment
Edited by don77, 22 April 2005 - 11:10 PM.
Similar Topics
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users
As Featured On:






