[help me please im a noob]

I keep on getting these error codes
Tcpip.sysj- address fffff8800167ef60 base at fffff88001602000, datestamp 4c15a458
Stop:oxooooood1 (0x0000000000000008,0x0000000000000002, 0x00000000000000000, 0xfffff8800167ef60)
i have reinstalled my comp a total of 5 times now, i would love if you guys and girls could help me fix this problem i can barley use my comp now it crashes so much!

[Advertisements]

 dump file for crash.txt   1.56KB   278 downloadshere is the dump file

[help me please im a noob]

 dump file for crash.txt   1.56KB   278 downloadshere is the dump file

[rshaffer61]

Hello noob.... Welcome to
GeeksToGo,


I'm sorry to hear about your issue. We will try to help you resolve this as soon as possible.

• Please understand we are all volunteers and we are not here all the time.
• Sometimes it may be a extended amount of time to get back to you. If it has been
  more then 3 days please shoot me a PM and I will try to get back to you quickly
  then.
• Please do the following and supply the requested information as needed. If you
  don't understand my instructions please ask and I will try to explain them
  clearer for you.
• Do not attempt any steps unless instructed or ask before to
  make sure they will not cause any further issues.

The explanation of your error is as follows:

0x000000D1: DRIVER_IRQL_NOT_LESS_OR_EQUAL
(Click to consult the online Win XP Resource Kit article.)
The system attempted to access pageable memory using a kernel process IRQL that was too high. The most typical cause is a bad device driver (one that uses improper addresses). It can also be caused by caused by faulty or mismatched RAM, or a damaged pagefile.

First thing we need to check is your memory.

If you have more than one RAM module installed, try starting computer with one RAM stick at a time.

NOTE Keep in mind, the manual check listed above is always superior to the software check, listed below. DO NOT proceed with memtest, if you can go with option A

B. If you have only one RAM stick installed...
...run memtest...

1. Download - Pre-Compiled Bootable ISO (.zip)
2. Unzip downloaded memtest86+-2.11.iso.zip file.
3. Inside, you'll find memtest86+-2.11.iso file.
4. Download, and install ImgBurn: http://www.imgburn.com/
5. Insert blank CD into your CD drive.
6. Open ImgBurn, and click on Write image file to disc
7. Click on Browse for a file... icon:



8. Locate memtest86+-2.11.iso file, and click Open button.
9. Click on ImgBurn green arrow to start burning bootable memtest86 CD:



10. Once the CD is created, boot from it, and memtest will automatically start to run. You may have to change the boot sequence in your BIOS to make it work right.

To change Boot Sequence in your BIOS

Reboot the system and at the first post screen (where it is counting up memory) start tapping the DEL button
This will enter you into the Bios\Cmos area.
Find the Advanced area and click Enter
Look for Boot Sequence or Boot Options and highlight that click Enter
Now highlight the first drive and follow the directions on the bottom of the screen on how to modify it and change it to CDrom.
Change the second drive to the C or Main Drive
Once that is done then click F10 to Save and Exit
You will prompted to enter Y to verify Save and Exit. Click Y and the system will now reboot with the new settings.


The running program will look something like this depending on the size and number of ram modules installed:




It's recommended to run 5-6 passes. Each pass contains very same 8 tests.

This will show the progress of the test. It can take a while. Be patient, or leave it running overnight.



The following image is the test results area:



The most important item here is the “errors” line. If you see ANY errors, even one, most likely, you have bad RAM.

[help me please im a noob]

thank you i will do that right now and i will tell you the results when i'm done.

[rshaffer61]

thank you i will do that right now and i will tell you the results when i'm done.

No problem and I will wait for your results.

[help me please im a noob]

so far no errors for one dimm stick and one pass.if it would help you,the ram is patriot ram ddr3 1333mhz, 2x4gb kit. running on the asus crosshair iv extreme mobo with a amd cpu at 3.2 gh 955 4 core

Edited by help me please im a noob, 21 February 2011 - 03:26 PM.

[rshaffer61]

Almost the same setup I have. So you are running the system on one memory module now or running the memtest on just the one memory module?

[help me please im a noob]

Mem test on one dimm I normal run with both dimms

[rshaffer61]

OK good job. once that one is done then test the other and let me know if it finds any errors on either.

[help me please im a noob]

So far no error on the first one how many times should I let it test like how many passes

[rshaffer61]

If it gooes through one complete pass which if I remember right is like 5 tests then shut down and replace with the other module and test it then.

[help me please im a noob]

Wow I missed a biggy ! My dimm timings were off same with the MHz could this have been the problem

[rshaffer61]

Possible I would set it for default and try it that way.

[help me please im a noob]

That's what I did and both dimms passed 2 with no errors

[help me please im a noob]

started up windows and guess what it crashed

Attached Files

•  agean.txt   1.56KB   200 downloads