[bubblleboi]

When i connect my extra hard drive with the cable and boot windows, windows says NTLDR missing, press trl + alt + del to restart or reboot and select another device to boot from.

The problem is that a while back, i was able to properly boot windows with my primary hard drive while the second hard drive was connected. The first thing i did was reformat my second hard drive to use it as another storage space. No problems here.

So i went ahead and moved as much of my files and data that i could to my second drive until it was full. still no problems.

Then, after quite some time, i rebooted my computer and during the normal boot up, at the screen where one is displayed with a fully black screen with a blinking little white "_". and for some reason, my computer never got past this point.

So i tried to isolate the problem by disconnecting the second drive and rebooting my computer and it worked fine. then i disconnected my primary drive and connected my storage drive and i was displayed with the "NTLDR missing" message.

I still have important files on this drive so i don't want to reformat!

Thanks in advance!

[Advertisements]

Hello bubblleboi.... Welcome to GeeksToGo,

I'm sorry to hear about your issue. We will try to help you resolve this as soon as possible.
Please understand we are all volunteers and we are not here all the time. Sometimes it may be a extended amount of time to get back to you. If it has been more then 3 days please shoot me a PM and I will try to get to you quickly then.

If you have Windows CD...

1. Insert your Windows XP CD into your CD and assure that your CD-ROM drive is capable of booting the CD.
2. Once you have booted from CD, do NOT select the option that states: Press F2 to initiate the Automated System Recovery (ASR) tool.
You’re going to proceed until you see the following screen, at which point you will press the “R” key to enter the recovery console:



3. After you have selected the appropriate option from step two, you will be prompted to select a valid Windows installation (typically number “1″).
Select the installation number, and hit Enter.
If there is an administrator password for the administrator account, enter it and hit Enter (if asked for the password, and you don't know it, you're out of luck).
You will be greeted with this screen, which indicates a recovery console at the ready:



4. There are eight commands you must enter in sequence to repair any of the issues I noted in the opening of this guide.
I will introduce them here, and then show the results graphically in the next six steps.
NOTE. Make sure, you press Enter after each command. Make sure, all commands are exact, including "spaces".
These commands are as follows:

CD..
ATTRIB -H C:\\boot.ini
ATTRIB -S C:\\boot.ini
ATRIB -R C:\\boot.ini
del boot.ini
BOOTCFG /Rebuild

Note about the above command.
BOOTCFG /REBUILD command which searches for pre-existing installations of Windows XP and rebuilds sundry essential components of the Windows operating system, recompiles the BOOT.INI file and corrects a litany of common Windows errors.
It is very important that you do one or both of the following two things:
A.) Every Windows XP owner must use /FASTDETECT as OS Load Option when the rebuild process is finalizing.
B.) If you are the owner of a CPU featuring Intel’s XD or AMD’s NX buffer overflow protection, you must also use /NOEXECUTE=OPTIN as an OS Load Option.
For the Enter Load Identifier portion of this command, you should enter the name of the operating system you have installed.
If, for example, you are using Windows XP Home, you could type Microsoft Windows XP Home Edition for the identifier (it's not crucial, however what the name is, as long, as it's meaningful).
Here is your computer screen:



5. Following command verifies the integrity of the hard drive containing the Windows XP installation. While this step is not an essential function in our process, it’s still good to be sure that the drive is physically capable of running windows, in that it contains no bad sectors or other corruptions that might be the culprit:

CHKDSK /R

6. This last command writes a new boot sector to the hard drive and cleans up all the loose ends we created by rebuilding the BOOT.INI file and the system files. When the Windows Recovery Console asks you if you are Sure you want to write a new bootsector to the partition C: ? just hit “Y”, then Enter to confirm your decision:

FIXBOOT

7. It’s time to reboot your PC by typing
EXIT
and pressing Enter.

With any luck, your PC will boot successfully into Windows XP as if your various DLL, Hive, EXE and NTLDR errors never existed.



2. If you don't have Windows CD...
Download Windows Recovery Console: http://www.thecomput...om/files/rc.iso
Download, and install free Imgburn: http://www.imgburn.c...hp?act=download
Using Imgburn, burn rc.iso to a CD.
Boot to the CD...let it finish loading.
When the "Welcome to Setup" screen appears, press R to start the Recovery Console.
Then, follow instructions from Step #3 above.

Thanks To Broni For The Instructions

[rshaffer61]

Hello bubblleboi.... Welcome to GeeksToGo,

I'm sorry to hear about your issue. We will try to help you resolve this as soon as possible.
Please understand we are all volunteers and we are not here all the time. Sometimes it may be a extended amount of time to get back to you. If it has been more then 3 days please shoot me a PM and I will try to get to you quickly then.

If you have Windows CD...

1. Insert your Windows XP CD into your CD and assure that your CD-ROM drive is capable of booting the CD.
2. Once you have booted from CD, do NOT select the option that states: Press F2 to initiate the Automated System Recovery (ASR) tool.
You’re going to proceed until you see the following screen, at which point you will press the “R” key to enter the recovery console:



3. After you have selected the appropriate option from step two, you will be prompted to select a valid Windows installation (typically number “1″).
Select the installation number, and hit Enter.
If there is an administrator password for the administrator account, enter it and hit Enter (if asked for the password, and you don't know it, you're out of luck).
You will be greeted with this screen, which indicates a recovery console at the ready:



4. There are eight commands you must enter in sequence to repair any of the issues I noted in the opening of this guide.
I will introduce them here, and then show the results graphically in the next six steps.
NOTE. Make sure, you press Enter after each command. Make sure, all commands are exact, including "spaces".
These commands are as follows:

CD..
ATTRIB -H C:\\boot.ini
ATTRIB -S C:\\boot.ini
ATRIB -R C:\\boot.ini
del boot.ini
BOOTCFG /Rebuild

Note about the above command.
BOOTCFG /REBUILD command which searches for pre-existing installations of Windows XP and rebuilds sundry essential components of the Windows operating system, recompiles the BOOT.INI file and corrects a litany of common Windows errors.
It is very important that you do one or both of the following two things:
A.) Every Windows XP owner must use /FASTDETECT as OS Load Option when the rebuild process is finalizing.
B.) If you are the owner of a CPU featuring Intel’s XD or AMD’s NX buffer overflow protection, you must also use /NOEXECUTE=OPTIN as an OS Load Option.
For the Enter Load Identifier portion of this command, you should enter the name of the operating system you have installed.
If, for example, you are using Windows XP Home, you could type Microsoft Windows XP Home Edition for the identifier (it's not crucial, however what the name is, as long, as it's meaningful).
Here is your computer screen:



5. Following command verifies the integrity of the hard drive containing the Windows XP installation. While this step is not an essential function in our process, it’s still good to be sure that the drive is physically capable of running windows, in that it contains no bad sectors or other corruptions that might be the culprit:

CHKDSK /R

6. This last command writes a new boot sector to the hard drive and cleans up all the loose ends we created by rebuilding the BOOT.INI file and the system files. When the Windows Recovery Console asks you if you are Sure you want to write a new bootsector to the partition C: ? just hit “Y”, then Enter to confirm your decision:

FIXBOOT

7. It’s time to reboot your PC by typing
EXIT
and pressing Enter.

With any luck, your PC will boot successfully into Windows XP as if your various DLL, Hive, EXE and NTLDR errors never existed.



2. If you don't have Windows CD...
Download Windows Recovery Console: http://www.thecomput...om/files/rc.iso
Download, and install free Imgburn: http://www.imgburn.c...hp?act=download
Using Imgburn, burn rc.iso to a CD.
Boot to the CD...let it finish loading.
When the "Welcome to Setup" screen appears, press R to start the Recovery Console.
Then, follow instructions from Step #3 above.

Thanks To Broni For The Instructions

[bubblleboi]

i don't have a windows xp cd.

after burning the image, but before i boot to the cd, do i connect my second drive with the cable? It is currently disconnected since i could not boot windows properly with it connected.

[rshaffer61]

You can but it will have no bearing on this because we are dealing with the Windows on the main drive.
The system is corrupted and the instructions should fix it.
If you want to be sure connect the second drive in and that way it will be detected automatically on bootup.

[hawklord]

on my machine if i boot to a drive without windows i get ntldr is missing,

is your storage drive a sata hdd and your windows drive an ide ?,
is the windows drive set to boot first when both drives are installed ?

[bubblleboi]

Hello bubblleboi.... Welcome to GeeksToGo,

I'm sorry to hear about your issue. We will try to help you resolve this as soon as possible.
Please understand we are all volunteers and we are not here all the time. Sometimes it may be a extended amount of time to get back to you. If it has been more then 3 days please shoot me a PM and I will try to get to you quickly then.

If you have Windows CD...

1. Insert your Windows XP CD into your CD and assure that your CD-ROM drive is capable of booting the CD.
2. Once you have booted from CD, do NOT select the option that states: Press F2 to initiate the Automated System Recovery (ASR) tool.
You’re going to proceed until you see the following screen, at which point you will press the “R” key to enter the recovery console:



3. After you have selected the appropriate option from step two, you will be prompted to select a valid Windows installation (typically number “1″).
Select the installation number, and hit Enter.
If there is an administrator password for the administrator account, enter it and hit Enter (if asked for the password, and you don't know it, you're out of luck).
You will be greeted with this screen, which indicates a recovery console at the ready:



4. There are eight commands you must enter in sequence to repair any of the issues I noted in the opening of this guide.
I will introduce them here, and then show the results graphically in the next six steps.
NOTE. Make sure, you press Enter after each command. Make sure, all commands are exact, including "spaces".
These commands are as follows:

CD..
ATTRIB -H C:\\boot.ini
ATTRIB -S C:\\boot.ini
ATRIB -R C:\\boot.ini
del boot.ini
BOOTCFG /Rebuild

Note about the above command.
BOOTCFG /REBUILD command which searches for pre-existing installations of Windows XP and rebuilds sundry essential components of the Windows operating system, recompiles the BOOT.INI file and corrects a litany of common Windows errors.
It is very important that you do one or both of the following two things:
A.) Every Windows XP owner must use /FASTDETECT as OS Load Option when the rebuild process is finalizing.
B.) If you are the owner of a CPU featuring Intel’s XD or AMD’s NX buffer overflow protection, you must also use /NOEXECUTE=OPTIN as an OS Load Option.
For the Enter Load Identifier portion of this command, you should enter the name of the operating system you have installed.
If, for example, you are using Windows XP Home, you could type Microsoft Windows XP Home Edition for the identifier (it's not crucial, however what the name is, as long, as it's meaningful).
Here is your computer screen:



5. Following command verifies the integrity of the hard drive containing the Windows XP installation. While this step is not an essential function in our process, it’s still good to be sure that the drive is physically capable of running windows, in that it contains no bad sectors or other corruptions that might be the culprit:

CHKDSK /R

6. This last command writes a new boot sector to the hard drive and cleans up all the loose ends we created by rebuilding the BOOT.INI file and the system files. When the Windows Recovery Console asks you if you are Sure you want to write a new bootsector to the partition C: ? just hit “Y”, then Enter to confirm your decision:

FIXBOOT

7. It’s time to reboot your PC by typing
EXIT
and pressing Enter.

With any luck, your PC will boot successfully into Windows XP as if your various DLL, Hive, EXE and NTLDR errors never existed.



2. If you don't have Windows CD...
Download Windows Recovery Console: http://www.thecomput...om/files/rc.iso
Download, and install free Imgburn: http://www.imgburn.c...hp?act=download
Using Imgburn, burn rc.iso to a CD.
Boot to the CD...let it finish loading.
When the "Welcome to Setup" screen appears, press R to start the Recovery Console.
Then, follow instructions from Step #3 above.

Thanks To Broni For The Instructions

This didn't work. Could it be because the command

CD.. only has 2 periods? and ATRIB -R C:\\boot.ini only has one T? I got the message "The command is not recognized Type HELP for a list of supported commands." after i entered these 2 commands

Edited by bubblleboi, 25 September 2009 - 08:57 PM.

[bubblleboi]

so just as an update, my computer still does the same thing when i connect my second hard drive to my mobo and i have a feeling that it is because of

CD.. only has 2 periods? and ATRIB -R C:\\boot.ini only has one T? I got the message "The command is not recognized Type HELP for a list of supported commands." after i entered these 2 commands