Jump to content

Welcome to Geeks to Go - Register now for FREE

Geeks To Go is a helpful hub, where thousands of volunteer geeks quickly serve friendly answers and support. Check out the forums and get free advice from the experts. Register now to gain access to all of our features, it's FREE and only takes one minute. Once registered and logged in, you will be able to create topics, post replies to existing threads, give reputation to your fellow members, get your own private messenger, post status updates, manage your profile and so much more.

Create Account How it Works
Photo

Please help...Desktop PC wont power on after power outage


  • Please log in to reply

#1
nofinga911

nofinga911

    Member

  • Member
  • PipPip
  • 39 posts
My power was out for hours today and has now been restored but my pc wont turn on. There is a solid green led lit in the back of the tower. I tried unplugging it for 10 minutes several times but its still not turning on. Any suggestions?
  • 0

Advertisements


#2
Digerati

Digerati

    Grumpy Ol' MSgt (Ret.)

  • Retired Staff
  • 3,997 posts
  • MVP
I would start by testing the PSU (see below) or swapping in a known good PSU.

The problem with power outages is they are not normally "clean". That is, power is not normally there one cycle, then gone the next. There are frequently little "flickers" which BANG, BANG, BANG on our electronics - never good. And also, when power returns, it typically does not return cleanly either. It often flickers, causing more banging on our electronics. The return can be worse because the power demands are SUPER HUGE when power is restored as refrigerators, air conditioners, lights and everything else tries to power up at the same time.

This is why all computers should be on a good UPS with AVR.

Testing PSUs:

To properly and conclusively test a power supply unit (PSU), it must be tested under various realistic "loads" then analyzed for excessive ripple and other anomalies. This is done by a qualified technician using an oscilloscope or power analyzer - sophisticated (and expensive) electronic test equipment requiring special training to operate, and a basic knowledge of electronics theory to understand the results. Therefore, conclusively testing a power supply is done in properly equipped electronic repair facilities.

Fortunately, there are other options that are almost as good. I keep a FrozenCPU Ultimate PSU Tester in my tool bag when I am "in the field" and don't have a good spare power supply to swap in. While not a certain test, they are better than nothing. The advantage of this model is that it has an LCD readout of the voltage. With an actual voltage readout, you have a better chance of detecting a "failing" PSU, or one barely within specified ATX Form Factor Standard tolerances. Lesser models use LEDs to indicate the voltage is just within some "range". These are less informative, considerably cheaper, but still useful for detecting PSUs that have already "failed". Newegg has several testers to choose from. All these testers contain a "dummy load" to fool the PSU into thinking it is connected to a motherboard, and therefore allows the PSU to power on, if able, without being attached to a motherboard - great for testing fans, but again, it is not a true load or suitable for conclusive testing.

Note the required voltage tolerance ranges:

Posted Image
NOTE: Disregard the -5VDC reading. It is no longer used.


Swapping in a known good supply is a tried and true method of troubleshooting used for years, even by pros. If you have access to a suitably sized, spare power supply, carefully remove the suspect supply and replace it with the known good one, and see if the problem goes away.

I do not recommend using a multimeter to test power supplies. To do it properly, that is, under a realistic load, the voltages on all the pins must be measured while the PSU is attached to the motherboard and the computer powered on. This requires poking (with some considerable force) two hard and sharp, highly conductive meter probes into the main power connector, deep in the heart of the computer. One tiny slip can destroy the motherboard, and everything plugged into it. It is not worth the risk considering most multimeters, like plug-in testers, do not measure, or reveal any unwanted and potentially disruptive AC components to the DC voltages.

Note the ATX Form Factor standard does not "require" specific color coding for power supply connector wiring. It has recommendations but manufacturers often do not follow them. Sadly, many testing guides or tutorials will refer to wire color only and that can lead to improper testing.

The voltages can be checked in the BIOS Setup Menus of most motherboards but they do not reveal ripple or other anomalies either. And of course, booting into the BIOS Setup Menu requires a working PSU.

As always, before working in the interior of the computer case, take necessary ESD precautions to ensure static buildup in your body does not discharge through and destroy any sensitive devices. Unplug from the wall and touch bare metal of the case before reaching in. And remember, anything that plugs into the wall can kill. Do not open the power supply's case unless you are a qualified electronics technician. There are NO user-serviceable parts inside a power supply. If you do not have a tester or a suitable spare to swap in, take the PSU to a qualified technician for testing.


  • 0






Similar Topics

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users

As Featured On:

Microsoft Yahoo BBC MSN PC Magazine Washington Post HP